VAMweld MIG & TIG Wire
Copper-coated MIG/CO₂ wire and mild steel TIG filler rods – supplied under the VAMweld brand, alongside our Mentrode electrodes.
Made for Everyday MIG & TIG Work
Good current pick-up at the contact tip and protection against rust in storage.
Consistent wire diameter for a steady arc and even bead.
MIG wire for production welding and TIG rods for clean, precise root passes and thin sheet.
Buy electrodes, MIG and TIG wire together – one order, one delivery.
Wire at a Glance
| Item | MIG / CO₂ Wire | TIG Filler Rods |
|---|---|---|
| Classification | AWS A5.18 ER70S-6 | AWS A5.18 ER70S-6 |
| Type | Copper-coated solid wire, layer wound | Copper-coated straight rods |
| Sizes | 0.8 mm · 1.2 mm | 1.6 mm · 2.4 mm · 3.2 mm |
| Length | On spool | 1000 mm |
| Packing | 15 kg spool | 5 kg pack |
| Shielding gas | 100% CO₂ or Ar + 15–25% CO₂ | 100% Argon |
| Polarity | DC+ (electrode positive) | DC− (electrode negative) |
Chemical Composition – ER70S-6 (%)
| C | Mn | Si |
|---|---|---|
| 0.06–0.15 | 1.40–1.85 | 0.80–1.15 |
| P | S | Cu |
| ≤ 0.025 | ≤ 0.035 | ≤ 0.50 |
Weld Metal – Minimum Requirements
| Tensile | Yield |
|---|---|
| ≥ 490 MPa | ≥ 400 MPa |
| Elongation | Impact |
| ≥ 22% | ≥ 27 J at −30 °C |
Values are the AWS A5.18 ER70S-6 specification limits. Mill test certificate available with each lot on request.
Typical MIG Parameters
Starting values for mild steel. Fine-tune for your machine, joint and position.
| Wire size | Best for | Current | Voltage | Gas flow | Stick-out |
|---|---|---|---|---|---|
| 0.8 mm | Sheet metal 0.8–3 mm, car bodies, light fabrication | 60 – 150 A | 16 – 21 V | 10 – 15 L/min | 8 – 12 mm |
| 1.2 mm | Plates 3 mm and above, structures, heavy fabrication | 120 – 300 A | 18 – 32 V | 15 – 20 L/min | 12 – 20 mm |
Use DC electrode positive (DC+). Keep the gas nozzle clean and shield the work from wind.
Mild Steel TIG Wire
Copper-coated mild steel filler rods, 1 metre long, for TIG (GTAW) welding – for root passes on pipe, thin sheet and neat, spatter-free welds.
| Rod size | Best for | Current (DC−) | Argon flow |
|---|---|---|---|
| 1.6 mm | Thin sheet and tube, 1–3 mm | 50 – 110 A | 6 – 10 L/min |
| 2.4 mm | General work and pipe root passes, 3–6 mm | 90 – 180 A | 8 – 12 L/min |
| 3.2 mm | Thicker sections, 6 mm and above | 150 – 250 A | 10 – 15 L/min |
Weld on DC electrode negative (DC−) with pure argon. Typical starting values for mild steel.
Where It's Used
Get a Price
Tell us the wire or rod size and quantity – we will send the price and delivery time.
Electrodes Too?
See the Mentrode E6013, E7016 and E7018 range – made at our plant in Palakkad, Kerala.


